U-Boot 2017.03 (Oct 03 2024 - 08:18:41 -0400)
CPU: Freescale i.MX6ULL rev1.1 696 MHz (running at 396 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 40C
Reset cause: POR
Model: Freescale i.MX6 ULL 14x14 EVK Board
Board: MX6ULL 14x14 EVK
DRAM: 512 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Display: TFT7016 (1024x600)
Video: 1024x600x24
In: serial
Out: serial
Err: serial
Net: No ethernet found.
Normal Boot
Hit any key to stop autoboot: 0
Error: “findtee” not defined
switch to partitions #0, OK
mmc1(part 0) is current device
switch to partitions #0, OK
mmc1(part 0) is current device
** Unrecognized filesystem type **
8846320 bytes read in 440 ms (19.2 MiB/s)
Booting from mmc …
39690 bytes read in 49 ms (791 KiB/s)
Kernel image @ 0x80800000 [ 0x000000 - 0x86fbf0 ]
Flattened Device Tree blob at 83000000
Booting using the fdt blob at 0x83000000
Using Device Tree in place at 83000000, end 8300cb09
Modify /soc/aips-bus@02200000/epdc@0228c000:status disabled
ft_system_setup for mx6
Starting kernel …
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.9.88 (book@100ask) (gcc version 7.5.0 (Buildroot 2020.02-gee85cab) ) #4 SMP PREEMPT Thu Mar 13 04:25:09 EDT 2025
[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c53c7d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt:Machine model: Freescale i.MX6 ULL 14x14 EVK Board
[ 0.000000] Reserved memory: created CMA memory pool at 0x8c000000, size 320 MiB
[ 0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] percpu: Embedded 15 pages/cpu @8bb2e000 s30156 r8192 d23092 u61440
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048
[ 0.000000] Kernel command line: console=ttymxc0,115200 root=/dev/mmcblk1p2 rootwait rw
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 172236K/524288K available (11264K kernel code, 1103K rwdata, 4040K rodata, 1024K init, 477K bss, 24372K reserved, 327680K cma-reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xa0800000 - 0xff800000 (1520 MB)
[ 0.000000] lowmem : 0x80000000 - 0xa0000000 ( 512 MB)
[ 0.000000] pkmap : 0x7fe00000 - 0x80000000 ( 2 MB)
[ 0.000000] modules : 0x7f000000 - 0x7fe00000 ( 14 MB)
[ 0.000000] .text : 0x80008000 - 0x80c00000 (12256 kB)
[ 0.000000] .init : 0x81100000 - 0x81200000 (1024 kB)
[ 0.000000] .data : 0x81200000 - 0x81313c70 (1104 kB)
[ 0.000000] .bss : 0x81315000 - 0x8138c6d8 ( 478 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 32.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=1
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] Switching to timer-based delay loop, resolution 333ns
[ 0.000018] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns
[ 0.000068] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns
[ 0.004510] Console: colour dummy device 80x30
[ 0.004564] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000)
[ 0.004607] pid_max: default: 32768 minimum: 301
[ 0.004861] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.004894] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.006578] CPU: Testing write buffer coherency: ok
[ 0.006680] ftrace: allocating 35227 entries in 104 pages
[ 0.140629] /cpus/cpu@0 missing clock-frequency property
[ 0.140684] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.140757] Setting up static identity map for 0x80100000 - 0x80100058
[ 0.229449] Brought up 1 CPUs
[ 0.229490] SMP: Total of 1 processors activated (6.00 BogoMIPS).
[ 0.229511] CPU: All CPU(s) started in SVC mode.
[ 0.231097] devtmpfs: initialized
[ 0.249164] OF: Duplicate name in lcdif@021c8000, renamed to “display#1”
[ 0.256508] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[ 0.257365] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.257424] futex hash table entries: 256 (order: 2, 16384 bytes)
[ 0.283866] pinctrl core: initialized pinctrl subsystem
[ 0.286526] NET: Registered protocol family 16
[ 0.306281] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.331551] cpuidle: using governor menu
[ 0.393319] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.393356] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.397863] imx6ul-pinctrl 20e0000.iomuxc: Invalid fsl,pins property in node /soc/aips-bus@02000000/iomuxc@020e0000/imx6ul-evk/enet1grp
[ 0.398711] imx6ul-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver
[ 0.399599] imx6ul-pinctrl 2290000.iomuxc-snvs: initialized IMX pinctrl driver
[ 0.546074] mxs-dma 1804000.dma-apbh: initialized
[ 0.554548] SCSI subsystem initialized
[ 0.564527] usbcore: registered new interface driver usbfs
[ 0.564748] usbcore: registered new interface driver hub
[ 0.565014] usbcore: registered new device driver usb
[ 0.567951] i2c i2c-0: IMX I2C adapter registered
[ 0.568006] i2c i2c-0: can’t use DMA, using PIO instead.
[ 0.570280] i2c i2c-1: IMX I2C adapter registered
[ 0.570332] i2c i2c-1: can’t use DMA, using PIO instead.
[ 0.571663] Linux video capture interface: v2.00
[ 0.571874] pps_core: LinuxPPS API ver. 1 registered
[ 0.571899] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti giometti@linux.it
[ 0.571964] PTP clock support registered
[ 0.575207] MIPI CSI2 driver module loaded
[ 0.576501] imx rpmsg driver is registered.
[ 0.577036] Advanced Linux Sound Architecture Driver Initialized.
[ 0.579348] Bluetooth: Core ver 2.22
[ 0.579487] NET: Registered protocol family 31
[ 0.579512] Bluetooth: HCI device and connection manager initialized
[ 0.579557] Bluetooth: HCI socket layer initialized
[ 0.579594] Bluetooth: L2CAP socket layer initialized
[ 0.579693] Bluetooth: SCO socket layer initialized
[ 0.594415] clocksource: Switched to clocksource mxc_timer1
[ 0.783452] VFS: Disk quotas dquot_6.6.0
[ 0.783643] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.813312] NET: Registered protocol family 2
[ 0.815091] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.815227] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.815389] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.815535] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.815597] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.816001] NET: Registered protocol family 1
[ 0.837352] RPC: Registered named UNIX socket transport module.
[ 0.837388] RPC: Registered udp transport module.
[ 0.837410] RPC: Registered tcp transport module.
[ 0.837431] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.844073] Bus freq driver module loaded
[ 0.859324] workingset: timestamp_bits=30 max_order=17 bucket_order=0
[ 0.890506] NFS: Registering the id_resolver key type
[ 0.890580] Key type id_resolver registered
[ 0.890604] Key type id_legacy registered
[ 0.890746] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.892706] fuse init (API version 7.26)
[ 0.912006] io scheduler noop registered
[ 0.912044] io scheduler deadline registered
[ 0.912546] io scheduler cfq registered (default)
[ 0.913889] imx-weim 21b8000.weim: Driver registered.
[ 0.923122] backlight supply power not found, using dummy regulator
[ 0.932749] sii902x 1-0039: No reset pin found
[ 0.936749] 21c8000.lcdif supply lcd not found, using dummy regulator
[ 1.073728] Console: switching to colour frame buffer device 128x37
[ 1.204549] mxsfb 21c8000.lcdif: Success seset LCDIF
[ 1.204591] mxsfb 21c8000.lcdif: initialized
[ 1.208320] imx-sdma 20ec000.sdma: loaded firmware 3.3
[ 1.220207] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 20, base_baud = 5000000) is a IMX
[ 1.922972] console [ttymxc0] enabled
[ 1.929129] 21ec000.serial: ttymxc2 at MMIO 0x21ec000 (irq = 73, base_baud = 5000000) is a IMX
[ 1.939733] 21fc000.serial: ttymxc5 at MMIO 0x21fc000 (irq = 74, base_baud = 5000000) is a IMX
[ 1.987307] imx-rng 2284000.rngb: iMX RNG Registered.
[ 1.993285] imx sema4 driver is registered.
[ 1.997811] [drm] Initialized
[ 2.002231] [drm] Initialized vivante 1.0.0 20120216 on minor 0
[ 2.205473] brd: module loaded
[ 2.277921] loop: module loaded
[ 2.292077] spi_gpio spi4: gpio-miso property not found, switching to no-rx mode
[ 2.305678] spi_imx 2008000.ecspi: probed
[ 2.312397] spi_imx 2010000.ecspi: probed
[ 2.319892] libphy: Fixed MDIO Bus: probed
[ 2.325383] CAN device driver interface
[ 2.332235] flexcan 2090000.can: device registered (reg_base=a0a00000, irq=29)
[ 2.343587] 20b4000.ethernet supply phy not found, using dummy regulator
[ 2.395768] pps pps0: new PPS source ptp0
[ 2.402541] libphy: fec_enet_mii_bus: probed
[ 2.421512] fec 20b4000.ethernet eth0: registered PHC device 0
[ 2.429035] 2188000.ethernet supply phy not found, using dummy regulator
[ 2.485616] pps pps1: new PPS source ptp1
[ 2.493693] fec 2188000.ethernet eth1: registered PHC device 1
[ 2.502086] PPP generic driver version 2.4.2
[ 2.507201] PPP BSD Compression module registered
[ 2.511977] PPP Deflate Compression module registered
[ 2.517309] PPP MPPE Compression module registered
[ 2.522155] NET: Registered protocol family 24
[ 2.526787] SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256) (6 bit encapsulation enabled).
[ 2.536647] CSLIP: code copyright 1989 Regents of the University of California.
[ 2.543996] SLIP linefill/keepalive option.
[ 2.548537] usbcore: registered new interface driver asix
[ 2.554148] usbcore: registered new interface driver ax88179_178a
[ 2.560529] usbcore: registered new interface driver cdc_ether
[ 2.566632] usbcore: registered new interface driver cdc_eem
[ 2.572472] usbcore: registered new interface driver net1080
[ 2.578387] usbcore: registered new interface driver cdc_subset
[ 2.584582] usbcore: registered new interface driver zaurus
[ 2.590410] usbcore: registered new interface driver cdc_ncm
[ 2.596188] ehci_hcd: USB 2.0 ‘Enhanced’ Host Controller (EHCI) Driver
[ 2.602798] ehci-platform: EHCI generic platform driver
[ 2.609198] ehci-mxc: Freescale On-Chip EHCI Host driver
[ 2.614656] random: fast init done
[ 2.618462] ohci_hcd: USB 1.1 ‘Open’ Host Controller (OHCI) Driver
[ 2.624851] ohci-platform: OHCI generic platform driver
[ 2.631009] usbcore: registered new interface driver cdc_acm
[ 2.636834] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 2.645159] usbcore: registered new interface driver usblp
[ 2.650839] usbcore: registered new interface driver cdc_wdm
[ 2.656847] usbcore: registered new interface driver usb-storage
[ 2.663186] usbcore: registered new interface driver usbserial
[ 2.669286] usbcore: registered new interface driver usbserial_generic
[ 2.676057] usbserial: USB Serial support registered for generic
[ 2.682230] usbcore: registered new interface driver option
[ 2.688044] usbserial: USB Serial support registered for GSM modem (1-port)
[ 2.695270] usbcore: registered new interface driver usb_ehset_test
[ 2.705076] 2184800.usbmisc supply vbus-wakeup not found, using dummy regulator
[ 2.715116] 2184000.usb supply vbus not found, using dummy regulator
[ 3.335574] 2184200.usb supply vbus not found, using dummy regulator
[ 3.346129] ci_hdrc ci_hdrc.1: EHCI Host Controller
[ 3.351139] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1
[ 3.384530] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
[ 3.392705] hub 1-0:1.0: USB hub found
[ 3.396864] hub 1-0:1.0: 1 port detected
[ 3.404246] mousedev: PS/2 mouse device common for all mice
[ 3.412597] input: 20cc000.snvs:snvs-powerkey as /devices/soc0/soc/2000000.aips-bus/20cc000.snvs/20cc000.snvs:snvs-powerkey/input/input0
[ 3.427703] imx6ul-pinctrl 20e0000.iomuxc: pin MX6UL_PAD_GPIO1_IO01 already requested by 2010000.ecspi; cannot claim for 2040000.tsc
[ 3.439944] imx6ul-pinctrl 20e0000.iomuxc: pin-24 (2040000.tsc) status -22
[ 3.446954] imx6ul-pinctrl 20e0000.iomuxc: could not request pin 24 (MX6UL_PAD_GPIO1_IO01) from group tscgrp on device 20e0000.iomuxc
[ 3.459133] imx6ul-tsc 2040000.tsc: Error applying setting, reverse things back
[ 3.466574] imx6ul-tsc: probe of 2040000.tsc failed with error -22
[ 3.474085] usbcore: registered new interface driver usbtouchscreen
[ 3.481110] Gt9xx driver installing..
[ 3.485402] goodix-ts 1-005d: GTP Driver Version: V2.8.0.2<2017/12/14>
[ 3.491987] goodix-ts 1-005d: GTP I2C Address: 0x5d
[ 3.497189] goodix-ts 1-005d: touch input parameters is [id x y w p]<5 800 480 1024 1024>
[ 3.505928] 1-005d supply vdd_ana not found, using dummy regulator
[ 3.512329] 1-005d supply vcc_i2c not found, using dummy regulator
[ 3.518793] goodix-ts 1-005d: Failed get pinctrl state:output_high
[ 3.525123] goodix-ts 1-005d: Success request irq-gpio
[ 3.530316] goodix-ts 1-005d: Success request rst-gpio
[ 3.535549] goodix-ts 1-005d: try to reset and read Guitar 0
[ 3.541246] goodix-ts 1-005d: Guitar reset
[ 3.576738] goodix-ts 1-005d: I2C Addr is 5d
[ 3.582693] goodix-ts 1-005d: IC Version: 911_1060
[ 3.589475] goodix-ts 1-005d: Driver set not send config
[ 3.626001] goodix-ts 1-005d: Use slot report protocol
[ 3.631797] input: goodix-ts as /devices/virtual/input/input1
[ 3.638223] goodix-ts 1-005d: INT num 84, trigger type:2
[ 3.644192] goodix-ts 1-005d: create proc entry gt9xx_config success
[ 3.650796] goodix-ts 1-005d: Alloc memory size:1534.
[ 3.655958] goodix-ts 1-005d: I2C function: without pre and end cmd!
[ 3.662375] goodix-ts 1-005d: Create proc entry success!
[ 3.672119] snvs_rtc 20cc000.snvs:snvs-rtc-lp: rtc core: registered 20cc000.snvs:snvs-r as rtc0
[ 3.682311] i2c /dev entries driver
[ 3.687748] IR NEC protocol handler initialized
[ 3.692334] IR RC5(x/sz) protocol handler initialized
[ 3.697552] IR RC6 protocol handler initialized
[ 3.702120] IR JVC protocol handler initialized
[ 3.706737] IR Sony protocol handler initialized
[ 3.711386] IR SANYO protocol handler initialized
[ 3.716165] IR Sharp protocol handler initialized
[ 3.720899] IR MCE Keyboard/mouse protocol handler initialized
[ 3.726809] IR XMP protocol handler initialized
[ 3.735093] pxp-v4l2 pxp_v4l2: initialized
[ 3.745145] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0)
[ 3.752109] Bluetooth: HCI UART driver ver 2.3
[ 3.756968] usb 1-1: new high-speed USB device number 2 using ci_hdrc
[ 3.764002] Bluetooth: HCI UART protocol H4 registered
[ 3.769395] Bluetooth: HCI UART protocol BCSP registered
[ 3.774985] Bluetooth: HCI UART protocol ATH3K registered
[ 3.781019] usbcore: registered new interface driver bcm203x
[ 3.787384] usbcore: registered new interface driver btusb
[ 3.797004] sdhci: Secure Digital Host Controller Interface driver
[ 3.803239] sdhci: Copyright(c) Pierre Ossman
[ 3.807960] sdhci-pltfm: SDHCI platform and OF driver helper
[ 3.817762] sdhci-esdhc-imx 2190000.usdhc: could not get ultra high speed state, work on normal mode
[ 3.827886] sdhci-esdhc-imx 2190000.usdhc: Got CD GPIO
[ 3.896389] mmc0: SDHCI controller on 2190000.usdhc [2190000.usdhc] using ADMA
[ 3.905211] sdhci-esdhc-imx 2194000.usdhc: could not get ultra high speed state, work on normal mode
[ 3.947203] hub 1-1:1.0: USB hub found
[ 3.951294] hub 1-1:1.0: 4 ports detected
[ 3.974522] mmc1: SDHCI controller on 2194000.usdhc [2194000.usdhc] using ADMA
[ 3.994283] ledtrig-cpu: registered to indicate activity on CPUs
[ 4.018682] usbcore: registered new interface driver usbhid
[ 4.024315] usbhid: USB HID core driver
[ 4.064275] wm8960 1-001a: No platform data supplied
[ 4.110264] mmc1: new DDR MMC card at address 0001
[ 4.126957] mmcblk1: mmc1:0001 S40004 3.64 GiB
[ 4.142458] mmcblk1boot0: mmc1:0001 S40004 partition 1 4.00 MiB
[ 4.159586] mmcblk1boot1: mmc1:0001 S40004 partition 2 4.00 MiB
[ 4.176714] mmcblk1rpmb: mmc1:0001 S40004 partition 3 4.00 MiB
[ 4.195215] mmcblk1: p1 p2 p3
[ 4.209289] imx-wm8960 sound: wm8960-hifi <-> 202c000.sai mapping ok
[ 4.221843] imx-wm8960 sound: snd-soc-dummy-dai <-> 2034000.asrc mapping ok
[ 4.229628] imx-wm8960 sound: wm8960-hifi <-> 202c000.sai mapping ok
[ 4.274518] usb 1-1.1: new high-speed USB device number 3 using ci_hdrc
[ 4.369229] NET: Registered protocol family 26
[ 4.376114] NET: Registered protocol family 10
[ 4.393809] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 4.401977] NET: Registered protocol family 17
[ 4.406784] can: controller area network core (rev 20120528 abi 9)
[ 4.413229] NET: Registered protocol family 29
[ 4.417857] can: raw protocol (rev 20120528)
[ 4.422170] can: broadcast manager protocol (rev 20161123 t)
[ 4.428109] can: netlink gateway (rev 20130117) max_hops=1
[ 4.435702] Bluetooth: RFCOMM TTY layer initialized
[ 4.442912] Bluetooth: RFCOMM socket layer initialized
[ 4.449620] Bluetooth: RFCOMM ver 1.11
[ 4.453440] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 4.459014] Bluetooth: BNEP filters: protocol multicast
[ 4.464705] Bluetooth: BNEP socket layer initialized
[ 4.469719] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 4.475897] Bluetooth: HIDP socket layer initialized
[ 4.481080] 8021q: 802.1Q VLAN Support v1.8
[ 4.485444] lib80211: common routines for IEEE802.11 drivers
[ 4.491607] Key type dns_resolver registered
[ 4.500306] cpu cpu0: Registered imx6q-cpufreq
[ 4.529808] Bluetooth: hci0: rtl: examining hci_ver=06 hci_rev=000b lmp_ver=06 lmp_subver=8723
[ 4.538599] Bluetooth: hci0: rtl: loading rtl_bt/rtl8723b_config.bin
[ 4.545167] bluetooth hci0: Falling back to user helper
[ 4.611108] imx_thermal 2000000.aips-bus:tempmon: Industrial CPU temperature grade - max:105C critical:100C passive:95C
[ 4.624000] input: gpio-keys as /devices/soc0/gpio-keys/input/input2
[ 4.631298] snvs_rtc 20cc000.snvs:snvs-rtc-lp: setting system clock to 1970-01-01 00:00:00 UTC (0)
[ 4.641003] ltemodule-pwr: disabling
[ 4.644705] wifi-pwr: disabling
[ 4.647866] ALSA device list:
[ 4.650846] #0: wm8960-audio
[ 4.666249] EXT4-fs (mmcblk1p2): couldn’t mount as ext3 due to feature incompatibilities
[ 4.937373] EXT4-fs (mmcblk1p2): recovery complete
[ 4.944210] EXT4-fs (mmcblk1p2): mounted filesystem with ordered data mode. Opts: (null)
[ 4.952552] VFS: Mounted root (ext4 filesystem) on device 179:2.
[ 4.959806] devtmpfs: mounted
[ 4.966107] Freeing unused kernel memory: 1024K
[ 5.218400] EXT4-fs (mmcblk1p2): re-mounted. Opts: data=ordered
Starting syslogd: OK
Starting klogd: OK
Running sysctl: OK
[ 5.709022] ds18b20_drv_init OK.
[ 5.726532] dht11_drv_init OK.
[ 5.756803] irda_drv_init OK.
Populating /dev using udev: [ 5.843441] udevd[176]: starting version 3.2.9
[ 5.961356] udevd[177]: starting eudev-3.2.9
[ 7.014107] inv-mpu6000-spi spi2.0: mounting matrix not found: using identity…
[ 7.415114] 8723bu: loading out-of-tree module taints kernel.
[ 7.951951] usbcore: registered new interface driver rtl8723bu
done
Initializing random number generator: OK
Saving random seed: OK
Starting system message bus: done
Starting network: [ 9.049861] Generic PHY 20b4000.ethernet-1:01: attached PHY driver [Generic PHY] (mii_bus:phy_addr=20b4000.ethernet-1:01, irq=-1)
[ 9.062312] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
OK
Starting ModemManager: OK
Starting NetworkManager … done.
Starting ntpd: OK
Starting mosquitto: OK
Starting pulseaudio: W: [pulseaudio] main.c: This program is not intended to be run as root (unless –system is specified).
[ 10.677544] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 10.686604] Generic PHY 20b4000.ethernet-1:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=20b4000.ethernet-1:00, irq=-1)
[ 10.699008] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 10.808344] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 12.475638] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 12.632380] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 12.759970] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 12.767253] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 12.880121] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 13.710783] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 13.766578] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
OK
Starting sshd: OK
Starting telnetd: OK
Starting swupdate: Trying to connect to SWUpdate…
OK
Connected to SWUpdate via /tmp/swupdateprog
Welcome to imx6ull buildroot system !
- SourceCode: https://gitee.com/weidongshan
- Support: https://support@100ask.net
- Shop： https://100ask.taobao.com/
- Login: name: root Passwd:
100ask login: root
COLUMNS=88;LINES=18;export COLUMNS LINES;
[root@100ask:~]# [ 69.655147] Bluetooth: hci0: Failed to load rtl_bt/rtl8723b_config.bin
[ 69.661764] Bluetooth: hci0: rtl: loading rtl_bt/rtl8723b_fw.bin
[ 69.692145] Bluetooth: hci0: rom_version status=0 version=1
[ 69.698229] Bluetooth: cfg_sz 0, total size 22768